Commercial Propulsion Engines C32 IMO II

Product Specifications for C32 IMO II

C32 IMO II Standard Equipment

AIR INLET SYSTEM

• Separate Circuit After-Cooled (SCAC

• Air cleaner

• Turbochargers, jacket water cooled

• Turbochargers inlet, 152 mm (6 in) OD straight connection

CONTROL SYSTEM

• Programmable Low Idle (550 - 750 rpm)

• WOSR (Wide Operating Speed Range) available for - A, B, & C Ratings

• Programmable High Idle Limit for WOSR Ratings

• Electronic diagnostics and fault logging

• Engine and transmission monitoring (speed, temperature, pressure)

• Electronic fuel/air ratio control

• Engine Protection Mode for extended ambient conditions

• Torque Limiting functionality for WOSR ratings only

• 70-pin customer connector

• Throttle Input signal options

COOLING SYSTEM

• Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX) & Keel cooled engines

• Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines

• SCAC pump, gear driven

• Jacket water pump, gear driven

• Sea water pump, bronze impeller, gear driven, for HEX cooled engines only

• Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard

• Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection

• SCAC and JW shunt tanks for maintaining proper pump inlet pressures

EXHAUST SYSTEM

• 4 Bolt 130 mm (5.12 in) diameter flanged outlet

• Water-cooled exhaust manifold & turbocharger

FLYWHEELS & FLYWHEEL HOUSINGS

• SAE standard rotation (CCW facing exciter end)

• Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth

FUEL SYSTEM

• Duplex Fuel Filters, Spin-on, RH & LH service

• Fuel connections size:Supply JIC 37 Deg -10 (7/8-14), Return JIC 37 Deg -8 (3/4-16)

• Plate Type Fuel Cooler installed behind Aftercooler Shunt Tank

• Fuel transfer pump, gear driven

• Manual fuel priming pump

• Hybrid fuel line design

LUBE SYSTEM

• Simplex Oil Filters, RH or LH service

• Deep sump oil pan

• RH or LH service oil filler locations

• RH or LH service dipstick

• Oil pump, gear driven

MOUNTING SYSTEM

• Front support - adjustable

POWER TAKE-OFFS

• Front Poly-V groove pulley (Quantity 1) for auxiliary drives

GENERAL

• Common electrical bonding point

• Engine does not ship with zinc components

C32 IMO II Optional Equipment

Air Inlet Systems

• Air Inlet Cleaner

• Air Inlet Adapter

Charging Systems

• Battery Charger

• Charging Alternators

• Ammeter

Cooling System

• Marine Gear/Transmission Oil Coolers

• Connections

Exhaust System

• Dual Elbow

• Flexible Fitting

• Dual Muffler

• Muffler Spark Arresting

• Flange

Fuel System

• Water Separator

Instrumentation

• OEM Wiring Harness

• Engine to Engine Harness

• Instrument Panels

• Exhaust Temperature Sensors

• Wiring Harness

• Gauges

• Transmission Sensors

Lube System

• Transmission Oil Cooler

• Manual Sump Pump

• Duplex Oil Filters

Protection System

• Fuel and Oil Shielding

Starting System

• Air Starting Motor

• Air Start Accessories

• Electric Starting Motors - Single 24 Volt

• Starting Aids

• Battery Sets - 24 Volt - Dry

• Dual Starting Motors (Electric and Air)

Packing

• Engine Protective Cover

• Export Packing

• Storage Preservation

Mounting System

• Front Support

• Adapter Kits

• Isolator Mounts

Power Take-Offs

• Front Enclosed Clutches

• Rear Hydraulic Pump Drive

GENERAL

• Fumes Disposal

CONTROL SYSTEM

• Instrument Panels

• CATERPILLAR ALARM AND PROTECTION

• Fuel and Oil Shielding