Offshore Drilling and Production Generator Sets C280-8

Product Specifications for C280-8

C280-8 Standard Equipment

Product Consist

• The engine is a turbocharged, aftercooled, four-strokecycle-diesel, electronic unit injection engine with a280 mm (11 in) bore by 300 mm (11.8 in) stroke. SAEstandard rotation is counterclockwise as viewed from therear of engine flywheel.

Emissions Certifications

• GL and CCS approved IMO certificate — includesstatement of compliance or Engine International AirPollution Prevention (EIAPP) certificate, supplied by theRecognized Organization (RO) where available, andtechnical file to be kept on board per IMO regulations.

Marine Certification Society type-approval

• ABS, BV, CCS, DnV, GL, LRS

• Spray shielding to meet SOLAS regulations for flammablefluids

European Certifications

• Declaration of Incorporation for EU Machinery Safety

• Directive and EU Low Voltage Safety Directive

Air Inlet System

• Fresh water aftercooler, corrosion resistant coated (airside)

• Air inlet shutoff

• Turbocharger, rear-mounted, oil lubricated

Control System

• Single Cat ADEM A3 electronic engine control module withelectronic unit injector fuel system, rigid wiring harness(10 amp 24V power required to drive electronic enginecontrol modules)

Cooling System

• Gear-driven jacket water (JW) pump

• Gear-driven separate-circuit aftercooler/oil cooler (AC/OC) pump

• Engine coolant water drains

Exhaust System

• Dry, gas tight exhaust manifold

Fuel System

• Distillate fuel (requires viscosity ranging from 1.4 cStto 20 cSt at 38°C)

• Fuel pump, gear-driven

• Fuel transfer pump (mounted on left-hand side)

• Duplex fuel filters, rear-engine-mounted

• Electronically controlled unitinjectors

Lube system

• Centrifugal oil filters with single shutoff, service-side enginemounted on cylinder block inspection covers (includesinstalled oil lines and single shutoff valve), filters centrifugebypass oil from the main lubricating oil pump (can be servicedwith the engine running)

• Oil filler and dipstick

• Oil pressure regulating valve

• Dry engine-mounted sump system that gravity feeds intobase assembly integral sump

• Engine-mounted duplex oil filter

• Intermittent air prelube

• Continuous electric prelube

• Redundant prelube with continuous electric prelube andintermittent air prelube backup

• Oil pan drain valves

• Electric continuous prelube pump

• Lube oil heater

• Oil pump - gear drive

Protection System

• Crankcase explosion relief valves

• Alarm and shutdown during abnormal operation

Instrumentation

• PLC-based system provides protection, monitoring, andcontrol housed in a NEMA 4 (IP66) enclosure.

General

• Service Literature

C280-8 Optional Equipment

Air Inlet System

• 90° adapter and straight adapters for air inlet to turbochargerAir cleaners

• Air cleaners with Cat dry paper filter elements (approximately99.9% efficient at filtering SAE fine dust)

• Soot filter

Control System

• 4-20 mA load feedback signal

• Load sharing module

• Direct rack module

Cooling System

• Separate Circuit Aftercooler (SCAC)

• Customer water connections

• Jacket water thermostats

• AC/OC thermostats

• Accessory module-mounted high volume expansion tank

• Jacket water heater

• Heat recovery connections and thermostats for use withwater maker system

• ANSI connection adapters

Exhaust System

• Exhaust manifold shields

• Vertical or 30° outboard exhaust orientation options

• Exhaust outlet expanders and weld flanges

Fuel System

• Manual fuel priming pump

• Duplex primary fuel strainer

• Flexible fuel hose connections

Lube System

• Dry engine-mounted sump system that gravity feeds intobase assembly integral sump

• Engine-mounted duplex oil filter

• Intermittent air prelube

• Continuous electric prelube

• Redundant prelube with continuous electric prelube andintermittent air prelube backup

• Oil pan drain valves

• Electric continuous prelube pump

• Lube oil heater

Protection System

• Wiring meets MCS requirements

• Upgrade PLC monitor to industrial PC

• Upgrades AC/OC, JW and start air pressure from contactorsto transducers

• Raw water/sea water pressure transducer

• Modbus communication

• Beacon and horn

• Single engine remote display monitor

• Emergency pump start signal

• Cabinet cooler

• Generator power monitoring

• Remote relay panel

• Turbocharger speed sensors

• Cylinder pressure relief valve

• Oil mist detector

• Flywheel and damper guards

Mounting System

• Base aseembly

• Vertically-restrained vibration isolators and weld plates

Starting System

• Single turbine air starters

• Boost control valve for extremely cold ambient conditions

• Air start pressure reducing valves

General

• Torsional couplings

• Mounting groups for engine, generator, and base

• Accessory module to mount attachments such as theexpansion tank, heat exchanger, instrument panel andengine controls, annunciator panel, alarm and shutdowncontactors, fuel strainer

• Flywheel

• Engine barring device options:

• One-year storage preservation

• Oceanic transportation shipping protection (shrink wrapand tarp)

• Engine testing — certified dynamometer test, fuelconsumption test, rated speed performance test, overloadtest, minimum power setting, peak firing pressure test,turbo work cert and crankshaft work cert

• Standard and project-specific witness testing

• Spare parts kits

Literature

• Project-specific installation drawings

• Electrical schematics and P&ID drawings