Well Service Engines C11 ACERT™ (Dry Manifold)

Product Specifications for C11 ACERT™ (Dry Manifold)

C11 ACERT™ (Dry Manifold) Standard Equipment

Air Inlet System

• Turbocharger, mid-mounted

• Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection

Control System

• Electronic governing, PTO speed control

• Programmable ratings

• Cold mode start strategy

• Automatic altitude compensation

• Power compensation for fuel temperature

• Programmable low and high idle and TEL

• Electronic diagnostics and fault logging

• Engine monitoring system — speed, temperature, pressure

• J1939 Broadcast — diagnostic and engine status

Cooling System

• Thermostats and housing

• Jacket water pump — gear-driven

• Front water pump inlet

Exhaust System

• Exhaust manifold — dry

• Front turbo exhaust

Flywheels and Flywheel Housings

• See Mandatory Options

Fuel System

• Electronic unit injector

• Fuel filter — secondary, mid-mount, (LH 2 micron high performance)

• Fuel transfer pump — front

• Fuel priming pump — LH mid-mount

Lube System

• Crankcase breather

• Oil cooler

• Oil filter — RH

• Oil pan — front sump, 40 L capacity

• Oil filler — LH front

• Oil dipstick — LH mid-mount

• Oil pump

• Oil valve sampling — on oil filter base

Power Take-Offs

• Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width

• Hydraulic pump drive — SAE A, 11 tooth

• 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)

General

• Vibration damper

• Paint — Cat yellow

• Lifting eyes

• Automatic variable timing, electronic

• Electronic installation kit (connectors, pins, sockets)

• Literature

Mandatory Options

• Flywheel housing or rear PTO

• Throttle position sensor

• Primary filter/water separator

C11 ACERT™ (Dry Manifold) Optional Equipment

Air Compressor

• Expansion chamber

• Governors

• Fittings

Air Inlet System

• Air cleaners

• Precleaners

• Turbo air inlet

• Air lines

Belt-Driven Accessories

• Refrigerant compressor and mounting

Charging System

• Charging alternators

• Alternator mountings

• Alternator guard

• Alternator accessories

Control System

• Connection

Cooling System

• Radiator — installed

• Fan drive f/u/w Caterpillar installed radiator

• Fan drive pulleys f/u/w customer-supplied radiators

• Coolant conditioner

• Water lines — pump inlet

• Fan drive mountings

• Fan height instructions

• Fan adapters for suction fans

• Fan adapters for blower fans

• Suction fans

• Blower fans

• Coolant level sensor

• Aftercooler lines

Exhaust System

• Muffler

• Flexible fitting

• Elbows

• Straight exhaust adapter

• Flange

• Pipe

• Rain cap

• Clamp

Fuel System

• Fuel lines

• Fuel cooler

• Fuel fitting — fuel return and supply connections

• Flexible fuel lines

Instrumentation

• Gauges and instrument panels

• Voltmeters

• Gauge mounting

• Ammeter

Lube System

• Oil pan

• Oil pan drain

• Oil level gauges

• Oil filter — bypass

• Oil filter — remote

• Lubricating oil

• Oil filler

• Fumes disposal

Mounting System

• Front and rear engine supports

• Structural steel base

Power Take-Offs

• Crankshaft pulleys

• Crankshaft pulley — stack-on

• Output flange

• Flywheel stub shaft

• Front stub shaft

• Hydraulic pump drive

• Hydraulic pumps — front

• Hydraulic pumps — rear

• Enclosed Clutch

• Clutch Support

Protection System

• Air shutoff

• Air shutoff switch

Starting System

• Electric starting motors — 12 Volt, 24 Volt

• Starting aids

• Battery sets — 24 Volt, dry

• Battery cable

• Battery rack

Transmission Arrangement

• Transmission cooler